The wire that comes with the kit is quite long so it will reach easily the only issue is that it can make it difficult to reassemble without the wire getting in the way. The whole process will only take a few seconds and if you get it right it will sit like a tiny dome shape on the metal contact you soldered to. Solder will only stick to hot metal, so the process involves heating the pad first with the tip of the soldering iron, melting a small amount of solder onto the pad while the iron is in place, and briefly leaving the iron in place afterwards to allow the solder to flow properly. You need to prepare two points with solder. Turn the screw until it is in place and no more – avoid overtightening as, again, this could permanently damage the plastic and cause an unsatisfactory fit. Then, turn clockwise and it should screw into place with little resistance. To avoid this happening, first turn the screw anticlockwise until you feel a little “pop” as the screw locates in the threaded hole. If you just screw straight in, you run the risk of it cutting a new thread and shearing off the plastic, preventing a secure fit. It should lift off easily, and the L and R buttons should remain attached to it.Ī note on reinserting screws into plastic: there will be a thread cut into the plastic from last time the screw was fitted, that you want the screw to go back into. Remove the back shell of the console and put it to one side. It’s a good idea to keep your screws organised as you go, as you’ll encounter more along the way – and they’re all different. Undo the four tri-wing at the corners as well as the one that was under the battery and another at the opening of the cartridge slot. Take out the battery one end will lift allowing for easy removal. Turn your Game Boy upside down, undo the crosshead screw on the battery cover and remove it from the console. Work on a soft surface free from debris you don’t want to scratch the top of your console when you flip it over. You’ll need a low wattage soldering iron with a stand and some soft solder, and if you have access to flux, a solder sucker and a pair of wire strippers – they’ll make for an easier job. It is entirely possible to install the screen with no soldering at all however, if you’re feeling adventurous there’s a simple one-wire soldering job that will allow you to adjust the brightness of your display – and believe us, it’s a great feature. In addition to this, a pair of scissors, some tweezers and a microfibre cloth will prove useful. Having a knife with a good point on it is also useful when removing the screw caps in the top of the shell. A Dremel-type power tool is quick and easy, but not everyone has access to one of those, so in this guide we'll focus on using a pair of side cutters and a sharp craft knife. Tools recommended for installing the kit are the aforementioned screwdrivers (be warned the quality of these isn’t great, so if you have better quality ones you’ll find the job easier) and cutting tools for removing the plastic. You can either purchase a new 600mAh battery or upgrade to an aftermarket 850mAh battery, which are available on eBay for less than $10. NOTE: We've noticed that these new IPS screens are quite power-hungry, so if your existing 600mAh Game Boy Advance battery is a bit long in the tooth, you might find stamina is low. Not every kit will come with the exact same parts, and always make sure the seller has a good reputation before placing an order. The AGS-001 Game Boy Advance SP may have been the first-ever Game Boy with a front-lit screen, but compared to modern backlit displays, it leaves a lot to be desired in terms of brightness, clarity and vibrance. Technically, the kits could be used to replace the screens in the backlit AGS-101 model using a different method, but honestly, those are best left as they are: pixel perfection. This guide is specific to the AGS-001 model of the SP, with the front-lit screen. These screens are slightly larger than the original display and feature bold, vibrant colours and adjustable levels of brightness. In this article, we are going to be looking at installing a new “IPS V2” replacement screen kit in a Game Boy Advance SP. Fan-made modifications are appearing all of the time which help augment and improve the tech which makes these handhelds tick, and one of the latest upgrades is a new IPS screen for the Game Boy Advance SP. The Game Boy line of consoles may be old news to Nintendo, but that doesn't mean it isn't still evolving.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |